Year:
Mileage:2
Harley-Davidson Touring photos
Harley-Davidson Touring tech info
Warranty:Vehicle does NOT have an existing warranty
Harley-Davidson Touring description
|
Another Killer Bagger by BR Hotrods! Once again we went straight to the dealership and started with a showroom fresh 2016 Roadglide Special. That means we were already toting cruise control, navigation, linked ABS brakes, the big touch screen radio etc. We rode it back to the shop, strapped it to the lift and went to town! Right off the bat we installed a Misfit Industries neck (to make room for the killer 30" wheel that was being machined for us), what the Misfit neck does is allow us to get a killer stance as well as a factory like ride while sporting the 30" wheel. This kit (safely) puts the rake and trail exactly where it needs to be, which allows you to rack up mile after mile on the highway or in town. Be prepared for the nay sayers that crow on and on about how "those bikes can't be ridden", tell them to give us a dollar for every mile thats on the odometer or pipe down.. We have actually put over 2000 miles on this one in just over the three weeks it has been completed just because it rides awesome! Once the neck was TIG welded and the billet trees were installed, we started mocking up the stretched tank, side covers, bags, and rear fender from the boys at TOL, and as usual they fit like a glove. We then installed the RWD wrap around front fender to check for any issues, and as usual none were found so it was sanded and coated with several coats of Urethane primer, once all the parts were cured we hand blocked every square inch, even the factory fairing. While we were getting everything ready for paint, we had the local Harley dealership install an S&S big bore kit that brought the cubes up to 106ci, but more importantly it was done utilizing (boost friendly) forged pistons, while they were in there we added a set of Screamin' Eagle 585 camshafts, adjustable pushrods, and had the cylinders and heads Diamond Cut for a killer look! Once the engine was back together we installed a fully polished/ ceramic coated, intercooled turbo kit from Trask Industries, it comes complete with all of the components needed for the installation right down to the proper injectors, clutch etc. With the engine mods and the intercooler boost provided by the turbo, we are right at 200hp, and that's power that is daily drivable and doing so on pump gas! The fact that we have put over 2000 miles on it in three weeks can attest to the drivability. To control this turbocharged powerhouse, we installed a (Thundermax) ECM with wideband O2 sensors and self learn function. Next to arrive was the custom 30" wheel from (Ryd Wheels), we waited a little over a month for it to be made and chromed but it was well worth it! While installing a larger wheel upfront, the last thing we were gonna do was leave a stock diameter brake rotor on it, so we had them machine a matching 18" brake rotor and installed an HHI six piston caliper to perform the clamping! Holding that bada$$ wheel and rotor is a set of (Performance Machine) ball milled and chromed lower legs, which house one half of the (instant up) air ride kit from (AirFXUSA). Moving on up the forks are a set of 10" Chisel handlebars from Harley Davidson, they put your hands at the most ergonomic angle for those long rides, gone are the days of your hands going to sleep! Attached to the bars are CVO lighted buttons (for night time cruising), and custom HD black and chrome grips. Speaking of the lighted buttons, they control a killer sound system, we installed a J&M 330 watt amp that pounds away at (just released) 6.71" fairing speakers that include a separate grill mounted tweeter, as nasty as the engine is, this stereo will have you wondering if it is still running! We didn't want to take away from the flowing lines on this one so the last thing we were going to do was slap some dead alligator looking seat on it, we started with a 2016 CVO seat and had it customized to fit the stretched tank, so you have a solo seat when you want to go show off, and two minutes later you have a very comfortable matching rear seat and backrest for your passenger. Moving on to the rear, we installed the rear half of the (AirFXUSA) air ride kit, these aren't just stamped steel C-6 Corvette shocks like everyone else uses, these are 6061 Billet aluminum rear shocks that have adjustable rebound for that perfect ride! We also upgraded to the hi-output compressor as well as a hidden air tank, so no more waiting on the pressure to build, just hit the switch and roll out! Speaking of the air ride, when it's fully dumped the bike rests on an MRI billet aluminum and anodized center stand that is electrically actuated, we also always leave the stock side stand on as well for customer preference. Next up is the paint, once the urethane primer was blocked to perfection we laid down a bright white base, followed by several coats of a custom pearl midcoat that made for a killer pearl white. We then locked it down with two coats of Glasurit clear and allowed it to cure. After block sanding all of the parts, we had our striper lay down a killer set of flames and fill them with 100% pure Italian copper, next up was three more coats of clear. Once that was cured, everything was blocked again before david hand striped all of the flames, we then applied four more coats of high-solid clear and allowed it to cure. A couple of days later it was all blocked again and buffed to a killer finish! We also painted the inner fairing just to tie everything together. Among the small things we added were A killer flamethrower kit for having fun at the shows! (Custom Dynamics) front turn/running LED's Custom LED tail/brake lights (Eddie Trotta) Rolex cut Floor boards, rear pegs, fork sliders and bag latches (Harley Davidson) low profile windshield (Camtech) BMF chin spoiler (Performance Machine) Billet aluminum horn cover (Harley Davidson) Billet Tribal mirrors (Screamin Eagle) 10mm plug wires (Harley Davidson) Chrome swingarm cover As you can see, no shortcuts were taken, it's simply a show quality bagger that has coast to coast drivability, thanks to modern technology and an intelligent approach to the selection of parts. Call or email with any questions. NEW lower reserve in order to get the next two rolling! |
Harley-Davidson Touring for Sale
2013 harley-davidson touring(US $41000)
1977 harley-davidson touring(US $34939)
2005 harley-davidson touring(US $39000)
1995 harley-davidson touring(US $18,500.00)
2006 harley-davidson touring(US $4,950.00)
1980 harley-davidson touring(US $24,500.00)
Moto blog
Don’t Run From This Cop – Video
Tue, 28 Jan 2014Quinn Redeker is one talented motorcycle rider. In this impressive video, watch as he wins a motorcycle skills competition aboard his motorcycle. And oh yeah, Redeker is a motorcycle cop.
Back to the Future
Wed, 26 Nov 2008Crocker Motorcycles. Who? Exactly.
Laconia Harley-Davidson and New Hampshire Motor Speedway to Raise $76K for Boys & Girls Clubs in World Record Attempt
Thu, 23 May 2013Laconia Harley-Davidson and New Hampshire Motor Speedway (NHMS) have teamed up to make the 90th Anniversary of Laconia Motorcycle Week even more historic through an effort to raise over $76,000 for the Boys & Girls Clubs of New Hampshire and set a new Guinness Worlds Record. Laconia Motorcycle Week attendees and New Hampshire residents will play a key role in this endeavor by purchasing tickets for a Community Appreciation Parade at New Hampshire Motor Speedway on the final Saturday of Bike Week, June 15th. Participants will have the unique opportunity to ride around the New Hampshire Motor Speedway track, continue on a police escorted, scenic 32-mile ride around the Lakes Region, set a new Guinness World Record and most importantly, raise significant funds for the Boys & Girls Clubs of New Hampshire.
Harley-Davidson Touring by State
| Harley-Davidson Touring by City
| Harley-Davidson Touring by Color |